Advance acoustic 908 7161 020 Скачать руководство пользователя страница 55

Страница: 55 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

ELECTRICAL SYSTEM

MACHINE WORKING HOUR CHECK (optional)

(For.

Adfinity

20 D, X 20 D, X 20 C, X 24 D

) Turn the ignition key (80) to “I”.

Press the vacuum system switch (73) and read on the hour counter (79) the total number of working hours (scrubbing/

drying) performed by the machine.

Turn off the vacuum system by pressing the switch (73).

(For.

Adfinity

20 D, X 20 D, X 20 C, X 24 D

) Turn the ignition key (80) to “0”.

BATTERY CHARGE AND MAINTENANCE

See the User Manual.

BATTERY DISASSEMBLY/ASSEMBLY

Disassembly

If the tank (21) contains recovery water:

Drive the machine to the appointed recovery water disposal area.

(For.

Adfinity

20 D, X 20 D, X 20 C, X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST, 20 ST

) Turn off the switches (71) and (73).

Empty the recovery water tank (21) with the hose (16).

Drive the machine on a level floor.

•. (For.

Adfinity

20 D, X 20 D, X 20 C, X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST, 20 ST

) Turn off the switches (71) and (73).

Disconnect the battery connector (12).

Grasp the handle (41) and carefully lift the tank (40).

Disconnect the cables (A) from the battery terminals.

Remove the battery shims, if present.

Carefully remove the batteries (B).

Assembly

Assemble the batteries in the reverse order of disassembly, referring to the installation diagram (C), and note the following:

Set the machine according to the type of batteries installed (WET or GEL) as shown in the relevant paragraph.

•

S301566A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Advance acoustic 908 7161 020, Высокого давления, Страница: 55 / 67

Результаты поиска

Содержание 908 7161 020

Отзывы: