Advance acoustic 908 7161 020 Скачать руководство пользователя страница 41

Страница: 41 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

RECOVERY WATER SYSTEM

RECOVERY WATER TANK AND VACUUM GRID CLEANING, AND COVER GASKET CHECK

Drive the machine to the appointed recovery water disposal area.

•. (For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Lift the cover (A) to washing position (L).

Wash with clean water the cover (A), the tank (B) and the vacuum grid with automatic shut-off float (D).

Drain the water in the tank through the hose (16).

If necessary, release the fasteners (E) and open the grid (D), recover the float (F), clean all the components and then

reinstall them.

Check the tank cover gasket (G) for integrity.

NOTE

The gasket (G) creates vacuum in the tank that is necessary for vacuuming the recovery water.

If necessary replace the gasket (G) by removing it from its housing (H). When assembling the new gasket, install the

joint (I) in the rear central area, as shown in the figure.

Check that the bearing surface (J) of the gasket (G) is integral and adequate for the gasket itself.

Check the compensation hole (K) for clogging, and clean it if necessary.

NOTE

The hole (K), allowing to compensate the air in the cover interspaces, contributes to create vacuum in the

tank.

Close the cover (A).

NOTE

Figure showing Adfinity

X 20 C.

•

S301551A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды