Advance acoustic 908 7161 020 Скачать руководство пользователя страница 38

Страница: 38 / 67

ENGLISH

SERVICE MANUAL

9096982000(1)2007-02

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

BRUSHING SYSTEM

CHECK/REPLACEMENT/ADJUSTMENT OF DRIVING BELTS FROM MOTORS TO CYLINDRICAL

BRUSHES (For Adfinity

X 20 C)

Check

Drive the machine on a level floor.

Turn the ignition key (12) to “0”.

Lower the cylindrical brush deck by pressing the pedal (11).

Remove the screws (A) and remove the covers (B).

Visually inspect the belt (C) for integrity, cuts, tears or cracks, otherwise replace it according to the following procedure.

Check the tension of the belt (G) according to the following procedure.

Replacement

If the belt (G) is to be replaced, loosen the nut (D) and move the pulley (K) to loosen the belt.

Tension the belt (according to the following procedure).

Belt tensioning

Check the tension of the belt (C) from motor to brush. The tension is correct:

When pressing the belt in its center with a force of 22 lb (10 kg) (F), the belt bends for 0.20 in (5 mm).

If necessary, tension the belt according to the following procedure:

Loosen the nut (D) and adjust the position of the pulley (E). When tensioning procedure has been carried out, tighten the

nut (D).

Repeat step 8.

Reset

If Perform steps 3 an d 4 in the reverse order.

•

10.

11.

12.

5 mm

S301548A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды