Advance acoustic 908 7161 020 Скачать руководство пользователя страница 17

Страница: 17 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

SOLUTION/CLEAN WATER SUPPLY SYSTEM

SOLENOID VALVE DISASSEMBLY/ASSEMBLY (For Adfinity

20 D - X 20 D - X 20 C - X 24 D)

Disassembly

(

For machines with brushes/pad-holders

) Remove the brushes/pad-holders.

Lower the deck by pressing the pedal (11).

(

For Adfinity

20 D

) Loosen the clamp (A) and disconnect the hoses (B) from the filter assembly (C).

Disconnect the union (D) from the solenoid valve (E) and recover the gasket.

Remove the screw (F), disconnect the connector (G) and recover the gasket.

Remove the nuts (H).

•. (

For Adfinity

20 D

) Remove the solenoid valve (E) with the hoses (B). If necessary, separate the hoses (B) from the

solenoid valve.

(

For Adfinity

X 20 D - X 20 C - X 24 D

) Move the solenoid valve (E) and disconnect it from the union (I).

Assembly

Assemble the components in the reverse order of disassembly.).

TROUBLESHOOTING

SMALL AMOUNT OF SOLUTION OR NO SOLUTION REACHES THE BRUSH

Possible causes

The solution/clean water filter is clogged/dirty (clean).

The solution/clean water tap is stuck closed (replace).

The solenoid valve is broken or there is an open in the electrical connection (replace the solenoid valve/repair the electrical

connection).

There is debris in the solution tank clogging the output hole (clean the tank).

There are debris in the solution/clean water hoses clogging the flow (clean the hoses).

THE SOLUTION/CLEAN WATER REACHES THE BRUSH ALSO WHEN THE MACHINE IS OFF

Possible causes

There is dirt or calcium deposit on the solenoid valve gasket (clean).

The solenoid valve is broken (replace).

•

S301523A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды