manualshive.com logo in svg

Advance acoustic 908 7161 020, Высокого давления, Страница: 24 / 67

Поделиться
Скачать
Advance acoustic 908 7161 020 Скачать руководство пользователя страница 24

ENGLISH

SERVICE MANUAL

24

9096982000(1)2007-02

Adfinity

TM

 17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

BRUSHING SYSTEM

BRUSH/PAD-HOLDER/CYLINDRICAL BRUSH DECK DISASSEMBLY/ASSEMBLY (For Adfinity

TM

 20 

D - X 20 D - X 20 C - X 24 D)

The machine can be equipped with either the brush/pad-holder deck (18a and 18b) or the cylindrical brush deck (18c), 

according to the following procedures.

CAUTION!

When the deck is installed/removed, it may be necessary to change the squeegee too, because they must 

have the same width. For correct matching of deck and squeegee, see the Squeegee Installation paragraph in 

the User Manual.

Disassembly

Drive the machine on a level floor.

Remove the brushes/pad-holders, as shown in the User Manual. Do not remove the cylindrical brushes.

Lower the brush/pad-holder deck by pressing the pedal (11). 

Remove the cotter pins (B), then remove the gas spring (A), if present.

Disconnect the brush/pad-holder motor electrical connection (D).

Disconnect the solution hose connection (E).

Remove the screws (C), then remove the brush/pad-holder deck (F).

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

When the machine is equipped with the cylindrical brush deck (18c), the gas spring (A) must not be installed.

NOTE

Figure showing Adfinity

TM

 20 D with one brush

1.

2.

3.

4.

5.

6.

7.

1.

•

F

E

C

D

B

A

B

S301531A

Содержание 908 7161 020




































































Отзывы:

Нет отзывов