Advance acoustic 908 7161 020 Скачать руководство пользователя страница 29

Страница: 29 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

BRUSHING SYSTEM

BRUSH MOTOR ELECTRICAL INPUT CHECK (For Adfinity

X 24 D)

WARNING!

This procedure must be performed by qualified personnel only.

Check

Remove the brushes, as shown in the User Manual.

Lower the deck by pressing the pedal (11).

Apply the amperometric pliers (A) on one cable (B) of the brush motor (C).

Turn the speed adjuster (84) to idle and turn the ignition key (80) to “I”.

Turn on the brushes by pressing the switch (71) and check that the motor electrical input is 5 - 7 A at 24 V. Turn off the

brushes by pressing the switch (71).

Turn the ignition key (80) to “0”.

Remove the amperometric pliers (A).

If the electrical input is higher, perform the following procedures to detect and correct the abnormal input:

NOTE

If the electrical input is higher than the maximum allowed value, the 3 battery warning lights (81) flash simultaneously.

Check the tightening of F1 fuse screw (see the procedure in Fuse Check/Replacement paragraph).

Check if there is dust or dirt (ropes, cables, etc.) on the brush hub.

Check the motor carbon brushes (see the procedure in the relevant paragraph).

Disassemble the motor (see the procedure in the relevant paragraph), and check the condition of all its components.

If the above-mentioned procedures do not lead to a correct electrical input, the motor must be replaced

(see the procedure in the relevant paragraph).

Reset

Perform steps 1 and 2 in the reverse order.

•

S301536A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды