Advance acoustic 908 7161 020 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 67

Advance acoustic 908 7161 020 Скачать руководство пользователя страница 48

ENGLISH

SERVICE MANUAL

48

9096982000(1)2007-02

Adfinity

TM

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

DRIVE SYSTEM

MAXIMUM SPEED POTENTIOMETER DISASSEMBLY/ASSEMBLY (Adfinity

TM

20 D, X 20 D, X 20 C,

X 24 D)

Disassembly

Disconnect the battery connector (12).

Operating inside the hole (A), loosen the threaded dowel and remove the maximum speed adjuster knob (B).

Unscrew the potentiometer mounting nut (C).

Remove the screws (D) and move the cover (E).

Cut the fastening clamp (F) and disconnect the potentiometer connector (G).

Open the clamp (H).

Remove the potentiometer with the relevant wiring harness (I).Check and replacement

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

Fasten the knob (B) with the potentiometer shaft (L) completely turned to the left and the hole (A) in the lower centre

part of the panel as shown in the figure.

Test the drive system and the maximum speed change.

1.

2.

3.

4.

5.

6.

7.

8.

•

9.

E

D

D

B

A

B

C

L

G

F

I

H

E

S301560A

«
...
46
47
48
49
50
...
»

Содержание 908 7161 020




































































Отзывы:

Нет отзывов