Advance acoustic 908 7161 020 Скачать руководство пользователя страница 22

Страница: 22 / 67

ENGLISH

SERVICE MANUAL

9096982000(1)2007-02

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

AXP

TROUBLESHOOTING

SMALL AMOUNT OF DETERGENT OR NO DETERGENT REACHES THE BRUSHES

Possible causes:

The detergent flow percentage is too low (check/change the percentage as shown in the User Manual).

The hydraulic circuit upstream of the detergent pump is not triggered (check if the hose (48) is filled and, if necessary,

perform one or more draining cycle, as shown in the relevant paragraph).

The pump is broken or there is an open in the electrical connection (replace the pump/repair the electrical connection).

There is debris in the detergent tank clogging the output hole (clean the tank).

There are debris in the detergent hoses clogging the detergent flow (clean the hoses).

The detergent flow control switch is malfunctioning (check that the warning light (78) turns on; if necessary, replace the

function electronic board).

The function electronic board is not set for the operation with AXP (if present, remove the jumper wire (J4) behind the

electronic board).

The function electronic board is faulty (replace).

THE DETERGENT REACHES THE BRUSHES ALSO WHEN THE MACHINE IS OFF

Possible causes:

The pump is broken (replace).

The one-way valve is broken (replace).

THERE IS WATER IN THE DETERGENT TANK

Possible cause:

The one-way valve is broken (replace).

THE AXP DOES NOT TURN ON WHEN PRESSING THE SWITCH (77) AND THE WARNING LIGHT (78) DOES NOT TURN

Possible causes:

The function electronic board is not set for the operation with AXP (if present, remove the jumper wire (J4) behind the

electronic board).

The function electronic board is faulty (replace).

S301568A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды