Advance acoustic 908 7161 020 Скачать руководство пользователя страница 46

Страница: 46 / 67

ENGLISH

SERVICE MANUAL

9096982000(1)2007-02

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

RECOVERY WATER SYSTEM

SQUEEGEE SPRING CHECK/REPLACEMENT (All models, with aluminium squeegee)

Check

Drive the machine on a level floor.

•. (For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Check that the springs (A) and (B) push the squeegee (C) on the floor correctly.

If necessary, disassemble and replace the springs according to the following procedure.

Disassembly

Remove the squeegee (see the procedure in the relevant paragraph).

Lift the deck by pressing the pedal (11).

Grasp the handlebar (2) and lower the front part of the machine.

Remove the cotter pin (D).

Disengage the end (E) of the left spring (F) from the housing (G).

Remove the left spring (F).

Repeat steps 8, 9 and 10 for the right spring (H).

Assembly

Assemble the springs by performing steps 5 to 11 in the reverse order.

TROUBLESHOOTING

THE VACUUM SYSTEM MOTOR DOES NOT TURN ON

The wiring harness between the function electronic board and the vacuum system relay is damaged or short-circuited

(check and repair).

The vacuum system relay is damaged (replace).

The wiring harness between relay and motor is damaged (repair).

The vacuum system fuse is open (replace).

The vacuum system motor carbon brushes are worn (replace).

The vacuum system motor is faulty (check the electrical input).

The function electronic board is damaged (replace).

DIRTY WATER VACUUMING IS INSUFFICIENT OR THERE IS NO VACUUMING

Possible causes

The vacuum grid with automatic shut-off float is activated because the recovery water tank is full (empty the recovery water

tank).

The vacuum grid with automatic shut-off float is dirty, or the vacuum pre-filter is dirty (clean).

The tank cover is not correctly positioned (adjust).

The tank cover gasket is not efficient, or the compensating hole is clogged (repair/clean).

The vacuum system motor filter is dirty (clean).

The squeegee or the vacuum hose is clogged or damaged (clean or repair/replace).

The vacuum gaskets are damaged or do not match perfectly (repair or replace).

THE SQUEEGEE LEAVES LINING ON THE FLOOR OR DOES NOT COLLECT WATER

Possible causes

There is debris under the blade (remove).

The squeegee blade edges are torn or worn (replace).

The squeegee is not balanced (adjust it with the relevant handwheel).

(For aluminium squeegee) The squeegee springs are not efficient (check/replace)

•

10.

11.

12.

S301557A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды