Advance acoustic 908 7161 020 Скачать руководство пользователя страница 16

Страница: 16 / 67

ENGLISH

SERVICE MANUAL

9096982000(1)2007-02

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

SOLUTION/CLEAN WATER SUPPLY SYSTEM

SOLUTION FILTER CLEANING (For Adfinity

20 D)

Drive the machine on a level floor.

Turn the ignition key (80) to “0”.

Close the solution tap (A) under the machine left lower side. The tap (A) is closed when it is on the position (B) and it is

open when it is on the position (C).

Remove the transparent cover (D), then remove the filter strainer (E). Clean and install them on the support (F).

NOTE

The filter strainer (E) must be correctly positioned on the housing (G) of the support (F).

Open the tap (A).

SOLENOID VALVE DISASSEMBLY/ASSEMBLY (For Adfinity

17 ST - 20 ST)

Disassembly

Remove the brush.

Lower the deck by pressing the pedal (11).

Remove the screw (A), disconnect the connector (B) and recover the gasket.

Disconnect the union (C) from the solenoid valve (D) and recover the gasket.

Remove the screws (E).

Slightly lift the solenoid valve (D), disconnect the union (F) and recover the gasket.

Recover the solenoid valve (D).

Assembly

Assemble the components in the reverse order of disassembly.

B A

S301521A

S301522A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды