Advance acoustic 908 7161 020 Скачать руководство пользователя страница 15

Страница: 15 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

SOLUTION/CLEAN WATER SUPPLY SYSTEM

SOLUTION/CLEAN WATER TANK AND SUPPLY SYSTEM CLEANING

Drive the machine to the appointed solution disposal area.

• (For Adfinity

20 D - X 20 D - X 20 C - X 24 D) Turn the ignition key (80) to “0”.

(For Adfinity

17 ST - 20 ST) Turn off the switches (71) and (73).

Empty the solution/clean water tank (20) with the hose (17).

Start the machine (as shown in the User Manual) and keep it running until the solution/clean water tank is completely

empty.

• (For Adfinity

20 D - X 20 D - X 20 C - X 24 D) Turn the ignition key (80) to “0”.

(For Adfinity

17 ST - 20 ST) Turn off the switches (71) and (73).

Clean the tank (20) with clean water.

Start the machine (as shown in the User Manual) and keep it running until the solution/clean water tank is completely

empty.

Clean the solution filter (see the following procedure).

SOLUTION FILTER CLEANING (For Adfinity

17 ST - 20 ST)

Drive the machine on a level floor.

Turn off the switches (71) and (73).

Close the solution tap (A) under the machine left lower side. The tap (A) is closed when it is on the position (B) and it is

open when it is on the position (C).

Remove the transparent cover (D), then remove the filter strainer (E). Clean and install them on the support (F).

NOTE

The filter strainer (E) must be correctly positioned on the housing (G) of the support (F).

Open the tap (A).

•

S301520A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды