Advance acoustic 908 7161 020 Скачать руководство пользователя страница 45

Страница: 45 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

RECOVERY WATER SYSTEM

VACUUM SYSTEM MOTOR DISASSEMBLY/ASSEMBLY

Disassembly

If the tank (21) contains recovery water:

Drive the machine to the appointed recovery water disposal area.

(For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Empty the recovery water tank (21) with the hose (16).

Drive the machine on a level floor.

•. (For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Disconnect the battery connector (12).

Grasp the handle (41) and carefully lift the tank (40).

Remove the screws (A) and recover the washers.

Remove the motor cover (B).

Remove the filter (C) and the gasket (D).

Remove the motor (E), the sound-deadening pipe (F) and the sound-deadening panel (G).

Disconnect the electrical connector (H) of the motor (E).

Check the efficiency of the gasket (I) and, if necessary, replace it.

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

If necessary, clean the filter (C) before assembling it (see the procedure in the relevant paragraph).

•

10.

11.

12.

•

S301556A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Advance acoustic 908 7161 020, Высокого давления, Страница: 45 / 67

Результаты поиска

Содержание 908 7161 020

Отзывы: