Advance acoustic 908 7161 020 Скачать руководство пользователя страница 6

Страница: 6 / 67

ENGLISH

SERVICE MANUAL

9096982000(1)2007-02

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

GENERAL INFORMATION

WARNING!

Always protect the machine against the sun, rain and bad weather, both under operation and inactivity condition.

Store the machine indoors.

Do not allow to be used as a toy. Close attention is necessary when used near children.

Use only as shown in this Manual. Only Nilfisk-Advance recommended accessories must be used.

Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine

moving parts.

Do not leave the machine unattended without being sure that it cannot move independently.

Do not use the machine on slopes with a gradient exceeding the specifications.

Do not use the machine in particularly dusty areas.

While using this machine, take care not to cause damage to people or objects.

Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.

Do not put any can containing fluids on the machine.

The machine working temperature must be b32°F and +104°F (0°C and +40°C).

The machine storage temperature must be b32°F and +104°F (0°C and +40°C).

The humidity must be between 30% and 95%.

Do not use the machine as a means of transport.

Do not use the machine on slopes with an inclination higher than 2%.

In case of fire, use a powder fire extinguisher, not a water one.

Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously.

Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. Always

keep the openings free from dust, hairs and any other foreign material which could reduce the air flow.

Do not remove or modify the plates affixed to the machine.

If the machine is used according to the instructions, the vibrations are not dangerous. The machine vibration level

is less than 2.5 m/s2 (98/37/EEC-EN 1033/1995).

This machine cannot be used on roads or public streets.

Pay attention during machine transportation when temperature is below freezing point. The water in the recovery

tank or in the hoses could freeze and seriously damage the machine.

Use brushes and pads supplied with the machine and those specified in the User Manual. Using other brushes or

pads could reduce safety.

If parts must be replaced, require ORIGINAL spare parts from a Dealer or Authorised Retailer.

Carefully read all the instructions before performing any maintenance/repair procedure.

Do not wash the machine with direct or pressurised water jets, or with corrosive substances.

The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, etc.),

which are subject to standards that require disposal in special centres (see the User Manual).

Do not pull or carry the machine by the battery charger cable and never use the battery charger cable as a handle.

Do not close a door on the battery charger cable, or pull the battery charger cable around sharp edges or corners.

Do not run the machine on the battery charger cable.

Keep the battery charger cable away from heated surfaces.

Do not charge the batteries if the battery charger cable or the plug are damaged. If the machine is not working as

it should, has been damaged, left outdoors or dropped into water, return it to the Service Center.

Before using the battery charger, ensure that frequency and voltage values, indicated on the machine serial

number plate, match the electrical mains voltage.

Do not smoke while charging the batteries.

To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged in.

Before performing any maintenance procedure, disconnect the battery charger cable from the electrical mains.

–

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды