Advance acoustic 908 7161 020 Скачать руководство пользователя страница 43

Страница: 43 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

RECOVERY WATER SYSTEM

VACUUM SYSTEM MOTOR FILTER CLEANING

Disassembly and cleaning

If the tank (21) contains recovery water:

Drive the machine to the appointed recovery water disposal area.

(For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Empty the recovery water tank (21) with the hose (16).

Drive the machine on a level floor.

•. (For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Grasp the handle (41) and carefully lift the tank (40).

Remove the vacuum system motor filter (44) and clean it with water and compressed air.

Install the filter (44).

Assembly

Assemble the components in the reverse order of disassembly.

VACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK

WARNING!

This procedure must be performed by qualified personnel only.

If the tank (21) contains recovery water:

Drive the machine to the appointed recovery water disposal area.

(For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For.

Adfinity

17 ST - 20 ST

) Turn off the switches (71) and (73).

Empty the recovery water tank (21) with the hose (16).

Drive the machine on a level floor.

•. (For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “0”.

(For) Turn off the switches (71) and (73).

Disconnect the battery connector (12).

Grasp the handle (41) and carefully lift the tank (40).

Apply the amperometric pliers (A) on one cable (B) of the batteries.

-. (For.

Adfinity

20 D - X 20 D - X 20 C - X 24 D

) Turn the ignition key (80) to “I”.

- Turn on the vacuum system by pressing the switch (73) and check that the motor electrical input is 16 - 19 A at 24 V.

Turn off the vacuum system by pressing the switch (73).

Remove the amperometric pliers (B).

If the electrical input exceeds the specifications, check the motor carbon brushes

(see the procedure in the relevant paragraph).

If necessary, disassemble the vacuum system motor (see the procedure in the relevant paragraph),

and check the condition of all its components.

If the above-mentioned procedures do not lead to a correct electrical input, the motor must be replaced

(see the procedure in the relevant paragraph).

Perform steps 4 and 5 in the reverse order.

•

S301553A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды