Advance acoustic 908 7161 020 Скачать руководство пользователя страница 23

Страница: 23 / 67

SERVICE MANUAL

ENGLISH

Adfinity

17 ST, 20 ST, 20 D, X 20 D, X 20 C, X 24 D

9096982000(1)2007-02

BRUSHING SYSTEM

BRUSH/PAD CLEANING

CAUTION!

It is advisable to wear protective gloves when cleaning the brushes/pads because there may be sharp debris.

Remove the brushes/pads, as shown in the User Manual.

Clean and wash the brushes/pads with water and detergent.

Check that the brush/pads are integral and not excessively worn; otherwise replace them.

(For.

Adfinity

X 20 C

) Remove the debris container (A) by pulling it on one side with the handle (B). Empty and wash the

debris container (A), and then install it by engaging it on the inside fasteners.

BRUSH/PAD-HOLDER BRUSH DECK DISASSEMBLY/ASSEMBLY (For Adfinity

17 ST - 20 ST)

The machine can be equipped with either the brush/pad-holder deck or the cylindrical brush deck.

Disassembly

Drive the machine on a level floor.

Remove the brushes/pad-holders, as shown in the User Manual.

Lower the brush/pad-holder deck by pressing the pedal (11).

Disconnect the brush/pad-holder motor electrical connection (A).

Remove the screw (B) and disconnect the electrical connection (C).

Disconnect the solution hose connection (D).

Remove the screws (F), then remove the brush/pad-holder deck (E).

Assembly

Assemble the components in the reverse order of disassembly.

S301529A

S301530A

Содержание 908 7161 020




































































Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды

Advance acoustic 908 7161 020, Высокого давления

Результаты поиска

Содержание 908 7161 020

Отзывы:

Похожие инструкции для 908 7161 020

Бренды по названию

Популярные бренды