Xerox WORKCENTRE 5735 System Administrator Manual Download Page 196

Page: 196 / 362

On Demand Overwrite

WorkCentre™ 5735/5740/5745/5755/5765/5775/5790
System Administrator Guide

196

Touch

[Print Report]

Touch

[Close].

On the Configuration Report, check under the

Installed Options

heading if

On Demand Image

Overwrite

is an installed and enabled option.

To Perform an Image Overwrite at the Device

This procedure will overwrite the image data from the hard disk. This excludes Embedded Fax data,
when this feature is installed on the device.

Note:

All existing jobs (excluding Embedded Fax), regardless of their state are deleted and all job

submission is prohibited for the duration of the overwrite. Do not switch off the device while
image overwrite is in progress.

Note:

The device must not be in diagnostics mode when the Overwrite is started.

Diagnostics Mode is used by a Customer Service Representative when servicing the device.

At the Device:

Note:

To configure this feature or these settings access the

Tools

pathway as a System

Administrator. For details, refer to

Access Tools Pathway as a System Administrator

on page 18.

From the

Tools

pathway, touch

[Security Settings]

Touch

[On Demand Overwrite]

Select one of the following:

•

Standard Image Overwrite

•

Full Image Overwrite

Touch

[Start Image Overwrite]

to start the Image Overwrite process.

The

Image Overwrite Confirmation

screen display. Touch

[Overwrite]

to begin. The device

will be taken offline and will be unable to receive any incoming jobs.

Following completion of the Overwrite the On Demand Overwrite completion screen appears.
Touch

[Close]

. The network controller will reboot and network functionality will be

unavailable for several minutes.

When rebooted, the Disk Overwrite confirmation report is printed. This details the status and time
of the overwrite.

To verify the overwrite has completed view the Confirmation Sheet, under Confirmation Details.
The Job Information: Status ESS Disk should read '

SUCCESS

To Perform an On Demand Overwrite over the Network

When the device has a network controller and is connected over the network, it is possible to run the
Image Overwrite function using a web browser. This is performed using Internet Services.

Note:

All existing jobs, regardless of their state, will be deleted and all job submission will be

prohibited for the duration of the overwrite. Do not switch off the device while image overwrite is
in progress.

Note:

The device must not be in diagnostics mode when the Overwrite is started.

Diagnostics Mode is used by a Customer Service Representative when servicing the device.

Summary of Contents for WORKCENTRE 5735











































































































































































































































































































































































Search results

Summary of Contents for WORKCENTRE 5735

Reviews:

Related manuals for WORKCENTRE 5735

Brands by name

Popular brands

Xerox WORKCENTRE 5735, System Administrator Manual

Search results

Summary of Contents for WORKCENTRE 5735

Reviews:

Related manuals for WORKCENTRE 5735

Brands by name

Popular brands