October 2012
2-62
ColorQube 8570/8870 Service Manual
94,510 ~ 94,513 , 94,524, 94,526
Revised, 3rd Revision - Xerox Internal Use Only
Fault Messages and Codes
94,510 ~ 94,513 Y-Axis Faults
A Y-Axis error has occurred. The following troubleshooting procedure applies to these errors.
Initial Actions
•
Reboot the printer and verify the error persists.
•
Check all the Drum cable connections.
•
If the problem persists, perform the following procedure.
Troubleshooting Reference
Applicable Parts (Chapter 5, Parts List)
•
Drum Assembly,
PL 2.1 Item 4
•
Y-Axis Motor Assembly,
PL 4.1 Item 2
•
Harness, Right Side Power Control,
PL 5.1 Item 13
Wiring and Plug/Jack References (Chapter 7, Wiring Data)
•
Figure 1
, Right Side Wire Routing
•
Figure 6
, Hard Drive, Drum Heater, Paper Preheater
•
Figure 7
, Drum Heater Load Dump, Motors, Head Maintenance Clutch, Strip Solenoid
Procedure
Check the Drum power and encoder wiring harness connectors
P/J114
,
P/J120
, and
P/J122
.
Are the connections secure and undamaged?
Y
N
Reseat and/or replace the wiring harness.
Clean the Y-Axis Belt and pulley with Isopropyl Alcohol. Power on the printer. Does the error
persist?
Y
N
Troubleshooting complete.
Replace the Y-Axis Belt (
REP 2.5
). Does the error persist?
Y
N
Troubleshooting complete.
Replace the Drum Assembly (
REP 2.4
). Does the error persist?
Y
N
Troubleshooting complete.
Replace the Y-Axis Motor Assembly (
REP 4.2
).
94,524, 94,526 Y-Axis Faults
A Y-Axis error has occurred. The following troubleshooting procedure applies to these errors.
Initial Actions
•
Reboot the printer and verify the error persists.
•
Check all the Drum cable connections.
•
If the problem persists, perform the following procedure.
Troubleshooting Reference
Applicable Parts (Chapter 5, Parts List)
•
Drum Assembly,
PL 2.1 Item 4
•
Y-Axis Motor Assembly,
PL 4.1 Item 2
•
Harness, Right Side Power Control,
PL 5.1 Item 13
Wiring and Plug/Jack References (Chapter 7, Wiring Data)
•
Figure 1
, Right Side Wire Routing
•
Figure 2
, Left Side Wire Routing
•
Figure 7
, Motors, Head Maintenance Clutch, Strip Solenoid
Procedure
Check the Drum Power and Encoder wiring harness connector
P/J122
. Is the connection
secure and undamaged?
Y
N
Reseat and/or replace the wiring harness.
Check the Y-Axis Motor wiring harness connector
P/J301
. Is the connection secure and
undamaged?
Y
N
Reseat and/or replace the wiring harness.
Clean the Y-Axis Belt and Pulley with Isopropyl Alcohol. Power on the printer. Does the error
persist?
Y
N
Troubleshooting complete.
Replace the Y-Axis Belt (
REP 2.5
). Does the error persist?
Y
N
Troubleshooting complete.
Replace the Drum Assembly (
REP 2.4
). Does the error persist?
Y
N
Troubleshooting complete.
Replace the Y-Axis Motor Assembly (
REP 4.2
).
Table 1 Applicable Fault Codes
94,510
Drum Image Initial Position
94,511
Drum stall During Imaging Acceleration
94,512
Drum stall During Imaging at Constant Velocity
94,513
Drum stall During Imaging Deceleration
Table 1 Applicable Fault Codes
94,524
Y-Axis Over Current Fault
94,526
Y-Axis Stall Fault
Summary of Contents for COLORQUBE 8570
Page 1: ...ColorQube 8570 8870 Printer ColorQube 8570 8870 Service Manual Xerox Internal Use Only...
Page 2: ......
Page 423: ......
