October 2012
2-6
ColorQube 8570/8870 Service Manual
PS NVRAM Reset
Revised, 3rd Revision - Xerox Internal Use Only
Fault Messages and Codes
PS NVRAM Reset
Many of the troubleshooting procedures in this section include an PS NVRAM reset as a pro-
cedural step. Following an NVRAM reset, the printer is unable to communicate on the network
and has lost several parameters specific to the customer’s configuration. If possible, print a
Configuration page to capture networking parameters. and discuss the customer’s configura-
tion to document these settings before resetting NVRAM.
Table 1
lists the parameters reset by NVRAM Reset. Required parameters (Yes) must be con-
figured to restore default printer operation on the network.
Table 1 Parameters Reset with Service Diagnostics PS NVRAM Reset Command
Menu
Parameter
Default
Required
Comment
TCP/IPv4 Setup
IPv4
On
Yes
DHCP/BOOTP
On
Yes
AutoIP
On
Yes
IPv4 Address
0.0.0.0
Yes
Set automati-
cally if DHCP/
BOOTP is
enabled
IPv4 Network Mask
0.0.0.0
Yes
Automatically
calculated
based on IP
Address
IPv4 Gateway
0.0.0.0
Yes
Automatically
set per RIP.
TCP/IPV6 Setup IPv6
Disabled
Yes
Auto Assign
On
Yes
Applicable
when IPv6 is
enabled.
Manual Address
Off
Yes
Appears when
IPv6 is enabled.
Network Ser-
vices
Port 9100
On
Yes
LPR
On
Yes
IPP
On
Yes
FTP
On
Yes
TFTP
On
Yes
WSD
On
Yes
SLP
Off
Yes
SSDP
Off
Yes
CentreWare IS
On
Yes
IPSec
Off
Yes
Network Setup
Ethernet Speed
Auto
Yes
EtherTalk
On
Yes
USB Setup
USB Port
On
Yes
Wait Timeout
30 secs
Yes
Page Description Language
AutoSelect
Yes
Control Panel
Setup
Language
English
No
Control Panel Brightness
8
No
Control Panel Contrast
5
No
Accessible Control panel
Off
No
Menu Timeout
30 secs
No
File Security
Overwrite Removals
Off
No
Daily Removal
Off
No
Age-based Removal
Off
No
Paper Handling
Setup
Paper Source
Auto
Select
No
2-Sided Printing
Off
No
Load Paper Timeout
3 mins
No
Letter/A4 Substitution
On
No
Custom Units
Inches
No
Cleaning Page Source
Highest
No
Printer Controls
Startup Page
On
No
Low Ink Warning Level
1000
No
Date and Time
NA
No
Set by on-board
RTC.
Warm-up Mode
Intelligent
Ready
No
Metric Defaults
Off
No
Fast Resume
Off
No
Paper Tray
Setup
Tray 1 Paper - Media Size
Guide Size
No
Tray 1 Paper - Media Type
Plain
No
Tray 2 Paper Type
Plain
No
Tray 3 Paper - (if installed)
Plain
No
Tray 4 Paper - (if installed)
Plain
No
Tray 5 Paper - (if installed)
Plain
No
Tray 1 Mode
Dynamic
No
Tray 1 Prompt
30 secs
No
Tray 2 Mode
Dynamic
No
Dependent on
number of
installed trays.
Tray 2-3 Mode
Dynamic
No
Dependent on
number of
installed trays.
Table 1 Parameters Reset with Service Diagnostics PS NVRAM Reset Command
Menu
Parameter
Default
Required
Comment
Summary of Contents for COLORQUBE 8570
Page 1: ...ColorQube 8570 8870 Printer ColorQube 8570 8870 Service Manual Xerox Internal Use Only...
Page 2: ......
Page 423: ......
