manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 35 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 35

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

33 

CPU OK indicator (green/red)

 

This bi-color LED indicates the CPU status is operational (green) or faulty (red). The CPU will flash fault 
codes (red) if they exist. This LED exists on both the Front Panel and back cover. 
 

IOLOCK indicator (red) 

Indicate the controller is shutdown and held in an IOLOCK state. This LED exists on both the Front Panel 
and back cover. 
 

ALARM indicator (yellow) 

Viewable from the front panel and controlled by GAP software. 
 

TRIPPED indicator (red) 

Viewable from the front panel and controlled by GAP software. 
 

Ethernet LED's 

(green=link, yellow=traffic) on each RJ45 connector indicate port status and operation. 
 

CPU Hardware Configuration 

The CPU Configuration Switch (S1) is reserved for future use and is not active at this time. 
 

Communications (Ethernet) 

 
There are (4) isolated RJ45 Ethernet Ports (10/100 Mbit/sec) available to the application software for 
system use. These ports are full duplex with auto crossover detection. 
 

Features 

 Interface 

standard: 

IEEE 802.3 (Ethernet) 

  Port Isolation: 1500 Vrms to PS, EARTH, and all other circuits 

  Control configuration using Woodward AppManager 

  Control monitoring, trending, and datalog collection 

  Control configuration of Ethernet IP addresses 

  General communications such as Modbus master/slave 

  Manage Configuration data and tunables with Control Assistant 

  Network time setup and control (SNTP) 

 

Network Configuration

. 

Ethernet ports (ETH1-4) can be configured for the customer network as desired. See the on-site Network 
Administrator to define an appropriate I/P address configuration. 
 

 

ETHERNET CABLES—Max cable length is 100 meters. To ensure 
signal integrity and robust operation, double shielded (SSTP) Cat5 
Ethernet cables are required for customer installations. 
(Woodward PN 5417-394, 10 feet) 

 

 

This module has been factory configured with fixed Ethernet IP 
addresses of 

 

Ethernet #1 (ETH1) = 172.16.100.15, Subnet Mask = 255.255.0.0 

 

Ethernet #2 (ETH2) = 192.168.128.20, Subnet Mask = 
255.255.255.0 

 

Ethernet #3 (ETH3) = 192.168.129.20, Subnet Mask = 
255.255.255.0 

 

Ethernet #4 (ETH4) = 192.168.130.20, Subnet Mask = 
255.255.255.0 

 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments