manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 31 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 31

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

29 

Environmental Specifications 

 

Table 2-1. Environmental Specifications 

 

Operating Temperature

1

 

–30 °C to +70 °C (with display) 

Storage Temperature 

–30 °C to +70 °C (recommended 10 °C to 40 °C) 

Vibration 

8.2 Grms, industrial skid mount, per Woodward 
RV1

 

Shock

2

 

10 G, 3x each axis, per Woodward MS1 
procedure 

Humidity

3,4

 

5 % to 95 %, non-condensing 

Altitude 3000m 

(9842 

ft.) 

Ingress Rating / 
Installation

5

 

IP20, Pollution Degree2, Overvoltage Category 
2 

Conformal coating 

Polyacrylate, sulfur resistant (see AppNote 
#51530) 

EMC Emissions

6

 

EN 61000-6-4 (Heavy Industrial) 
IACS UR E10 (Commercial Marine) 

EMC Immunity

6

 

EN 61000-6-2 (Heavy Industrial) 
IACS UR E10 (Commercial Marine) 

1

Limited by LCD display 

2

Limited by internal relay specification 

3

Relative humidity levels of < 55% will prolong LCD life 

4

Cyclic condensing humidity is supported with an appropriate enclosure 

5

ATEX, IP-54, and Pollution Degree 3 are supported with an appropriate enclosure using the 

ATEX/Marine qualified unit. 

6

Marine specification applies to the ATEX/Marine qualified unit 

 

Maintenance Info and Recommendations 

 
The 505 Control is designed for continuous operation in a typical industrial environment and includes no 
components that require periodic service. However, to take advantage of related product software and 
hardware improvements, we recommend that your product be sent to a Woodward Authorized Service 
Facility after every five to ten years of continuous service for inspection and component upgrades. 
 

Clock battery 

The Real Time Clock (RTC) battery is designed to last approximately 10 years during normal turbine 
operation. When powered, the RTC automatically disables the battery usage to preserve it. During power-
off the battery is enabled and only used to maintain date and time. For long term storage, the battery is 
specified to last > 5 years. 
 
The RTC battery is a replaceable lithium coin cell Woodward PN 1743-1017. Contact a Woodward 
Authorized Service Center if a replacement service is needed. 
 

Calibration and Functional verification 

It is recommended to verify calibration and functional operation every 24-36 months. This is especially 
important for spare units that need to be ready for immediate use. Contact a Woodward Authorized 
Service Center for assistance. 
 

Aluminum Electrolytic capacitors 

It is recommended to apply power to spare units every 24-36 months for 3 hours to reform the electrolytic 
capacitors used in the power module. 
 
 

 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments