manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 162 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 162

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

160 

After about 1:15 

TRIPPED=ON (RED)

 

   IOLOCK 

= 

OFF 

   CPU 

= 

ON 

(GREEN) 

 

After about 1:50 

ALARM LED (YELLOW)  

Flashes/Blinks

 

 

After about 4:30   Screen = HOME

 

 

 

 

Figure 5-2. 505 Splash Screen 

 
Any time that a Display application program is not running, the ‘Splash Screen’ will appear. If at power-up 
the Alarm LED stops flashing and this screen still appears – then the GUI program has not initialized 
correctly. 
 
Once the unit has been configured, all following power cycles will result in a screen similar to the 
following, dependent on what functionality has been configured. The numbers in () indicate that there is a 
quick keypad command to get to that screen. For example pressing 2 will jump to the Speed Control 
screen, from that screen if you press 7 it will jump to the Startup Curve screen. From any operational 
screen, pressing HOME will always return to this screen 
 

 

 

Figure 5-3. Boot-up to HOME Screen 

 
Refer to Figure 4.1 for the view of an initial power-up of a non-configured unit. 
 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments