manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 205 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 205

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

203 

Addr Description 

Addr 

Description 

1:0053  Trip - Tie Breaker Open 

1:0324 

Trip - Open Wire on MPUs 

1:0054  Trip - Gen Breaker Open 

1:0325 

Trip - LP Actuator Failed 

1:0055  Trip - Power up 

1:0326 

Trip - Overspeed Test Limit Reached 

1:0056  Trip - Manual Stop 

1:0327 

Trip - spare_40 

1:0057  Trip - External Trip 4 

1:0328 

Contact In 17 Closed 

1:0058  Trip - External Trip 5 

1:0329 

Contact In 18 Closed 

1:0059  Trip - Extraction Input Failed 

1:0330 

Contact In 19 Closed 

1:0060  Trip - External Trip 6 

1:0331 

Contact In 20 Closed 

1:0061  Trip - External Trip 7 

1:0332 

Relay 2 Energized 

1:0062  Trip - External Trip 8 

1:0333 

Inlet Is Enabled 

1:0063  Trip - External Trip 9 

1:0334 

Inlet Is Active 

1:0064  Shutdown Exists (Trip Indication) 

1:0335 

Inlet Is In Control 

1:0065  Modbus ESD Acknowledge Enable 

1:0336 

Inlet Active / Not Limiting 

1:0066  Moving to Min Setpoint 

1:0337 

Inlet Active / Not In Control 

1:0067  Ramping to Idle (Idle / Rated) 

1:0338 

Inlet is Inhibited 

1:0068  Idle / Rated at Idle 

1:0339 

Remote Inlet Is Enabled 

1:0069  Ramping to Rated (Idle / Rated) 1:0340 

Remote 

Inlet Is Active 

1:0070 At 

Rated 

1:0341 

Rmt Inlet Is In Control 

1:0071  Auto Seq - Setpt at Idle 1 

1:0342 

Rmt Inlet Is Inhibited 

1:0072  Auto Seq - Ramp to Idle 2 

1:0343 

Inlet Limiter Configured 

1:0073  Auto Seq - Setpt at  Idle 2 

1:0344 

Inlet Control Configured 

1:0074  Auto Seq - Ramp to rated 

1:0345 

Remote Inlet Configured 

1:0075  Auto Seq - At Rated 

1:0346 

Remote KW Setpt Is Enabled 

1:0076  Speed PID In Control 

1:0347 

Remote KW Setpt Is Active 

1:0077  Speed Sensor 1 Failed Overide ON 

1:0348 

Remote KW Setpt Is In Control 

1:0078  Speed Sensor 2 Failed Overide ON 

1:0349 

Remote KW Setpt Is Inhibited 

1:0079  Overspeed Test Permissive 

1:0350 

Remote KW Control Configured 

1:0080  Overspeed Test In progress 

1:0351 

* IHB Configured 

1:0081  Speed At or above Min Gov 

1:0352 

Enables Mod Port2 In Local 

1:0082  Turbine In Critical Speed Band 

1:0353 

Enables Mod Port3 In Local 

1:0083  Remote Speed Setpt Is Enabled 

1:0354 

Relay 2 is Level Switch 

1:0084  Remote Speed Setpt Is Active 

1:0355 

Relay 3 is Level Switch 

1:0085  Remote Speed Setpt Is In Control 

1:0356 

Relay 4 is Level Switch 

1:0086  Remote Speed Setpt Is Inhibited 

1:0357 

Relay 5 is Level Switch 

1:0087  Speed PID In Control (not being lmted) 

1:0358 

Relay 6 is Level Switch 

1:0088  Auto Seq - at idle 3 

1:0359 

Relay 7 is Level Switch 

1:0089  Spare 

1:0360 

Relay 8 is Level Switch 

1:0090  Generator  Breaker Closed 

1:0361 

Extraction Active / Not Limiting 

1:0091  Utility Tie Breaker Closed 

1:0362 

Extraction Active / Not In Control 

1:0092 Synchronizing 

Rate 

Selected 

1:0363 

Extraction Limiter Configured 

1:0093 Synchronizing 

Is 

Enabled 

1:0364 

Extraction Control Configured 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments