manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 164 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 164

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

162 

User Login Levels 

 
Pressing the MODE key at any time will open the Login and Mode Screen 
 

 

 

Figure 5-5. Mode Screen 

 

Monitor – 

(logout to enter this)

 

Even Keypad Green keys inhibited 

Operator – 

(passwords are provided in Vol 2 Appendix C)

 

Intended for normal turbine operation – default mode 
Screen saver initiates to this level 

Service – 

(passwords are provided in Vol 2 Appendix C) 

Allows tuning of parameters, while turbine is running (PID dynamics) and entering of Calibration Mode 

Configure – 

(passwords are provided in Vol 2 Appendix C) 

Highest user authority / can enter any Mode 
 

 

EMERGENCY STOP is always available in all modes and logins as it 
has direct H/W action to open the Actuator circuits. 

 

 

To Login –

 

1. 

Press the LOGIN button

 

2.  ** Navigate so the Login or Password field is highlighted (in-focus) 
3. Press 

Enter

 on the Navigation Cross 

4.  Use the keypad to enter the text field 

(hold key down to scroll options)

 

5. Press 

Enter

 on the Navigation Cross – to accept your entry 

 
** Or you can navigate to the Autofill buttons and press Enter – it will auto-populate the Login information 
so you only need to enter the Password. 
 
 

 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments