manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 155 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 155

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

153 

Event 
ID 

Description Error 

Meaning 

65 KW 

CASC 

Configured,CASC AI 
Configured 

The Cascade control function was configured to use the kW 
analog input but an Cascade analog input was configured also. 
With this configuration, only the kW analog input is used for the 
Cascade controller. 

66 Remote 

Casc 

Configured, No AI 

The Remote Cascade set point control function was configured 
but no Remote Cascade set point analog input was configured. 

67 

Inlet Pres CASC Config, 
CASC AI Config 

The Cascade control function was configured to use the Inlet 
Pressure analog input but an Cascade analog input was 
configured also. With this configuration, only the Inlet Pressure 
analog input is used for the Cascade controller. 

68 

Exhaust Press CASC 
Config, CASC AI Config 

The Cascade control function was configured to use the Exhaust 
Pressure analog input but an Cascade analog input was 
configured also. With this configuration, only the Exhaust Pressure 
analog input is used for the Cascade controller. 

69 

Exhaust Press CASC 
Config, No AI Config 

The Cascade control function was configured to use the Exhaust 
Pressure analog input but no AI is configured to be the Exhaust 
Pressure input 

70 Remote 

Speed 

Configured, No AI 

The remote speed set point control function was configured but no 
remote speed set point analog input was configured. 

71 Feed 

Forward 

Programmed, No AI 

The Feed Forward function was configured but no Feed Forward 
analog input is configured. 

72 

Sync and Sync/Load 
Share Configured 

Both the synchronizing analog input and the sync/load share or 
load share analog inputs are configured. If the application needs 
to perform both synchronizing and load sharing with analog 
signals, only the sync/load sharing analog input needs to be 
configured. 

73 

Load Share and 
Frequency Arm Cnfg 

Both the frequency arm/disarm function and the load share control 
functions are configured. Only one of these modes can be 
programmed — either freq arm/disarm OR Load Sharing. 

74 Generator 

Application, 

No Tie Breaker 

The unit is configured for a generator application but no utility tie 
breaker contact input is configured. This is a requirement. 

75 Generator 

Application, 

No Gen Breaker 

The unit is configured for a generator application but no generator 
breaker contact input is configured. This is a requirement. 

76 

Idle 1 in Critical Band 

Either the Idle speed set point (when using Idle/Rated) or the Idle 
1 set point (when using the Automatic Start sequence) is 
configured within a critical speed avoidance band. 

77 

Idle 2 in Critical Band 

The Idle 2 speed set point (when using the Automatic Start 
sequence) is configured within a critical speed avoidance band. 

78 

Idle 3 in Critical Band 

The Idle 3 speed set point (when using the Automatic Start 
sequence) is configured within a critical speed avoidance band. 

79 

Min Control Speed < 
Failed Speed Level 

Either the Idle speed set point (when using Idle/Rated) or the Idle 
1 set point (when using the Automatic Start sequence) is 
configured lower than the Failed Speed Level for speed input 1 or 
2. 

80 

Idle 1 Setpoint > 
Minimum Governor 

The Idle Speed setpoint is configured at a higher speed than the 
minimum governor speed setpoint. 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments