manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 154 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 154

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

152 

Event 
ID 

Description Error 

Meaning 

48 

Actuator 01 Readout 
Error 

The Actuator/Driver channel readout was configured for a function 
that is not configured as used. Either the readout was mis-
configured or the function required is mis-configured. For example, 
readout is configured for Cascade Set Point but Cascade Control 
was not configured under the Cascade Program Block. 

49 

Actuator 02 Readout 
Error 

See "Actuator 01 Readout Error". 

50 

Max KW Load > Max 
KW AI Scale 

The KW Max Load setting was programmed at a higher value than 
the maximum KW input (KW input at 20 mA). 

51 

Selected KW Source Not 
Configured 

Occurs when a Primary or Secondary kW Signal source has been 
selected under Operating Parameters but that source is not 
configured. For example, Primary kW Source is set as 'Analog 
Input' but no analog input is configured as a kW Input. 

52 

Turbine Type Requires 
LP Valve 

The unit is configured for Extraction/Admission and requires an LP 
Valve Driver to be configured 

53 

No LP Valve on this 
Turbine Type 

The unit is configured for as a Single Valve unit, but an LP Valve 
Driver has been configured 

54 

Auxiliary Configured, No 
AI 

The Auxiliary control function was configured but no Auxiliary 
analog input was configured. 

55 

KW AUX Configured, 
AUX AI Configured 

The Auxiliary control function was configured to use the kW 
analog input but an Auxiliary analog input was configured also. 
With this configuration, only the kW analog input is used for the 
Auxiliary controller. 

56 Remote 

AUX 

Configured, No AI 

The Remote Auxiliary set point control function was configured but 
no Remote Auxiliary set point analog input was configured. 

57 

Duplicate LP Configured  There is more than 1 selection for the LP valve demand output 

58 

Wrong Product Model 
Detected 

The Hardware model number does not match the Application.  

59 

Alternate Mode Map 
Error 

The D1-D6 values defining the Steam Map that will result from 
entering an alternate mode are incorrect. Either the sign (+/-) or 
the magnitude (less than 1e-6) is incorrect on one of these terms. 
For Exhaust Control modes, this is generally caused by incorrect 
settings of the Inlet, Extraction, or Exhaust Max Flow values. 

60 Spare60 

N/A 

61 Spare61 

N/A 

62 Spare62 

N/A 

63 Spare63 

N/A 

64 Cascade 

Configured, 

No 

AI 

The Cascade control function was programmed but no Cascade 
analog input was configured. 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments