manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 165 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 165

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

163 

Navigation 

 
This is NOT a touchscreen! Due to quality, robustness, screen cleanliness and long term reliability 
concerns Woodward chose not to implement a touchscreen directly on this product. Using the 
RemoteView tool a user can take advantage of either a mouse device or a touchscreen on an external 
computer, but for navigation and selection directly on the 505 display, buttons and an IN-Focus 
highlighter indication are used. 
 
In general, the maroon buttons provide navigation from page-to-page and throughout the components on 
a page. Most of the navigation is done with the Navigation cross. 
 

 

 

Figure 5-6. Navigation Cross 

 
1.  Use the “Arrow” buttons to move the IN-Focus highlighter to the desired page 
2.  Press the “Enter” button to launch the page selected 
3.  Press the “ESC” (Escape) button to go back 1 page from current page 

4. 

Press the “HOME” button to return to the main menu 

Note: If in Service or Configure menu a second 

press of HOME will return to the Operational Home screen 

 

 

 

Figure 5-7. Service Menu showing “Speed Control” IN-Focus 

 

Page Organization 

 
There are three primary menu lists that organize the access to all of the information that is available on 
the display. These menu lists are available at all times. The user simply uses the navigation cross to 
Focus on the desired page and press Enter, or use the the Black ‘soft keys’ (no Focus needed). 
 

Run/Operation menus

 - The HOME page contains the Run/Operation menus and is automatically 

updated to match the configuration of the control. 
 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments