manualshive.com logo in svg

Woodward 505XT, Installation And Operation Manual, Page: 13 / 242

Share
Download
Woodward 505XT Installation And Operation Manual Download Page 13

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

11 

 
Protective Earth Grounding of the 505XT is required to be connected to the PE terminal. 
 
A switch or circuit breaker shall be included in the building installation that is in close proximity to the 
equipment and within easy reach of the operator. The switch or circuit breaker shall be clearly marked as 
the disconnecting device for the equipment. The switch or circuit breaker shall not interrupt the Protective 
Earth (PE) conductor. 
 

Hazardous Locations 

 
Wiring must be in accordance with Zone 2 wiring methods and in accordance with the authority having 
final jurisdiction. 
 
The Real Time Clock Battery located on the CPU board is not to be recharged and is not user 
replaceable. Contact a Woodward Authorized Service Center if a replacement service is needed. 
 
The Low Voltage ATEX 505XT is suitable for use in Class I, Div 2, Gas Groups A, B, C and D & 
European Zone 2, Group IIC environments. 
 
This equipment must be installed in an area or enclosure providing adequate protection against high 
impact. (7 Joules) The control is rated for 2 Joules impact. 
 
ATEX/IECEx locations require that the 505XT Control be installed in a cabinet or enclosure coded Ex nA 
or Ex e that provides a minimum IP54 ingress protection for the rear of the control per IEC 60529. The 
front bezel, keypad and display have been tested and are rated IP54 while the rear of the control is rated 
IP20 due to the ventilation slots required for heat dissipation. The installer shall ensure that the maximum 
surrounding air temperature in the enclosure does not exceed the rated temperature of +70

˚

C. 

 
Transient Protection for the 505XT is to be provided externally by the end user at the supply terminals of 
the control. The transient protection device is to be set at a level not exceeding 140% of the peak rated 
voltage (36Vdc). 
 

 

Explosion Hazard

 

For ATEX/IECEx installation compliance, the input voltage shall be 
limited to 36 Vdc.  When an external power supply is selected to 
supply the Control, it shall be IECEx approved for Class 1, Division 2 
Applications. 

 

 

Explosion Hazard

 

Due to the Hazardous Location Listings associated with this product, 
proper wire type and wiring practices are critical to the operation. 

 

 

Explosion Hazard

 

ENCLOSURE REQUIREMENT— 
ATEX/IECEx Zone 2, Category 3G applications require the final 
installation location provide a minimum IP-54 ingress protection 
enclosure against dust and water per IEC 60529. The enclosure must 
be coded Ex nA or Ex e. 

 

 

Explosion Hazard

 

Do not remove covers or connect/disconnect electrical connectors 
unless power has been switched off and the area is known to be non-
hazardous. 

 

Summary of Contents for 505XT



















































































































































































































































Reviews:

No comments