WCH CH32V003 Series Reference Manual Download Page 46

Page: 46 / 181

CH32V003

Reference Manual

V1.3

[3:2]

IACTS2_3

2#-3# interrupt execution status.
1: current number interruption in execution.
0: The current number interrupt is not executed.

[1:0]

Reserved

6.5.2.20 PFIC interrupt activation status register 2 (PFIC_IACTR2)

Offset address: 0x304

Reserved

IACTS [38:32]

Bit

Name

Access

Description

Reset value

[31:7]

Reserved

[6:0]

IACTS32_38

32#-38# Interrupt execution status.
1: Current number interruption in execution.
0: The current number interrupt is not
executed.

6.5.2.21 PFIC Interrupt Priority Configuration Register (PFIC_IPRIORx) (x=0-63)

Offset address: 0x400-0x4FF

The controller supports 256 interrupts (0-255), each using 8 bits to set the control priority.

24 23

16 15

8 7

IPRIOR63

PRIO_255

PRIO_254

PRIO_253

PRIO_252

…

IPRIORx

PRIO_(4x+3)

PRIO_(4x+2)

PRIO_(4x+1)

PRIO_(4x)

…

IPRIOR0

PRIO_3

PRIO_2

PRIO_1

PRIO_0

Bit

Name

Access

Description

Reset value

[2047:2040]

IP_255

Same as IP_0 description.

…

[31:24]

IP_3

Same as IP_0 description.

[23:16]

IP_2

Same as IP_0 description.

[15:8]

IP_1

Same as IP_0 description.

[7:0]

IP_0

Number 0 interrupt priority configuration.
[7:6:4]: priority control bits.
If no nesting is configured, no preemption
bits.
Bit7 is preempted if 2 levels of nesting are
configured.
[5:0]: reserved, fixed to 0, write invalid.

6.5.2.22 PFIC System Control Register (PFIC_SCTLR)

Offset address: 0xD10

Summary of Contents for CH32V003 Series






















































































































































































Search results

Summary of Contents for CH32V003 Series

Reviews:

Brands by name

Popular brands

WCH CH32V003 Series, Reference Manual

Search results

Summary of Contents for CH32V003 Series

Reviews:

Brands by name

Popular brands