manualshive.com logo in svg

WCH CH32V003 Series, Reference Manual

Share
Download
WCH CH32V003 Series Reference Manual Download Page 103

CH32V003

 

Reference Manual

 

 

http://wch.cn

 

 

V1.3

 

 

103 

   

 

Reserved 

BG  TG  COMG CC4G CC3G CC2G CC1G  UG 

 

Bit 

Name 

Access 

Description 

Reset 

value 

[15:8]  Reserved 

RO  Reserved 

0 

7 

BG 

WO 

The brake event generation bit, which is set and cleared 
by software, is used to generate a brake event. 
1:  Generate  a  brake  event.  At  this  point,  MOE=0, 
BIF=1,  if  the  corresponding  interrupt  and  DMA  are 
enabled,  the  corresponding  interrupt  and  DMA  are 
generated. 
0: No action. 

0 

6 

TG 

WO 

The  trigger  event  generation  bit,  which  is  set  by 
software and cleared by hardware, is used to generate a 
trigger event. 
1:  Generate  a  trigger  event,  TIF  is  set,  and  the 
corresponding  interrupts  and  DMAs  are  generated  if 
enabled. 
0: No action. 

0 

5 

COMG 

WO 

Compare  capture  control  update  generation  bit. 
Generates a compare capture control update event. This 
bit  is  set  by  software  and  automatically  cleared  by 
hardware. 
1: when CCPC = 1, allow updating of CCxE, CCxNE, 
OCxM bits. 
0: No action. 

Note:  This  bit  is  only  valid  for  channels  with 
complementary outputs (channels 1, 2, 3). 

0 

4 

CC4G 

WO 

Compare  capture  event  generation  bit  4.  generates 
compare capture event 4. 

0 

3 

CC3G 

WO 

Compare  capture  event  generation  bit  3.  generates 
compare capture event 3. 

0 

2 

CC2G 

WO 

Compare  capture  event  generation  bit  2.  generates 
compare capture event 2. 

0 

1 

CC1G 

WO 

Compare  capture  event  generation  bit  1.  generates 
compare capture event 1. 
This bit is set by software and cleared by hardware. It 
is used to generate a compare capture event. 
1:  Generate  a  compare  capture  event  on  compare 
capture channel 1. 
If compare capture channel 1 is configured as 
output. 
Set  the  CC1IF  bit.  Generate  the  corresponding 
interrupts and DMAs if they are enabled. 
If compare capture channel 1 is configured as input. 
The current core counter value is captured to compare 
capture  register  1;  set  the  CC1IF  bit  to  generate  the 
corresponding interrupts and DMAs if they are enabled; 
if CC1IF is already set, set the CC1OF bit. 
0: No action. 

0 

0 

UG 

WO 

Update  event  generation  bit  to  generate  an  update 
event. This bit is set by software and is automatically 
cleared by hardware. 
1: Initialize the counter and generate an update event. 
0: No action. 

Note: The prescaler counter is also cleared to zero, but 
the  prescaler  factor  remains  unchanged.  The  core 
counter  is  cleared  if  in  centrosymmetric  mode  or 

0 

Summary of Contents for CH32V003 Series






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands