WCH CH32V003 Series Reference Manual Download Page 41

Page: 41 / 181

CH32V003

Reference Manual

http://wch.cn

V1.3

Writing 1 is valid, writing 0 is invalid.

Note: Same function as the PFIC_SCTLR register
SYSRESET bit.

[6:0]

Reserved

RO Reserved

6.5.2.7 PFIC interrupt global status register (PFIC_GISR)

Offset address: 0x4C

Reserved

GPE

STA

GAC

STA

NESTSTA[7:0]

Bit

Name

Access

Description

Reset value

[31:10]

Reserved

GPENDSTA

Are there any interrupts currently on hold.
1: Yes; 0: No.

GACTSTA

Are there any interrupts currently being executed.
1: Yes; 0: No.

[7:0]

NESTSTA

Current interrupt nesting status, currently supports
a maximum of 2 levels of nesting and a maximum
hardware stack depth of 2 levels.
0x03: Level 2 interrupt in progress.
0x01: Level 1 interrupt in progress.
Other: no interrupt occurred.

6.5.2.8 PFIC VTF interrupt ID configuration register (PFIC_VTFIDR)

Offset address: 0x50

Reserved

VTFID1

VTFID0

Bit

Name

Access

Description

Reset value

[31:16]

Reserved

[15:8]

VTFID1

Configure the interrupt number of

VTF

interrupt 1.

[7:0]

VTFID0

Configure the interrupt number of VTF interrupt
0.

6.5.2.9 PFIC VTF interrupt 0 address register (PFIC_VTFADDRR0)

Offset address: 0x60

18 17

ADDR0[31:16]

ADDR0[15:1]

VTF0E

Summary of Contents for CH32V003 Series






















































































































































































Search results

Summary of Contents for CH32V003 Series

Reviews:

Brands by name

Popular brands

WCH CH32V003 Series, Reference Manual

Search results

Summary of Contents for CH32V003 Series

Reviews:

Brands by name

Popular brands