manualshive.com logo in svg

WCH CH32V003 Series, Reference Manual

Share
Download
WCH CH32V003 Series Reference Manual Download Page 152

CH32V003

 

Reference Manual

 

 

http://wch.cn

 

 

V1.3

 

 

152 

   

 

13.11.2 I2C Control register 2(I2C1_CTLR2) 

Offset address: 0x04 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

LAST  DMA

EN 

ITBU

FEN 

ITEV

TEN 

ITER

REN  Reserved 

FREQ[5:0] 

 

Bit 

Name 

Access 

Description 

Reset value 

[15:13]  Reserved 

RO  Reserved 

0 

12 

LAST 

RW 

DMA last transfer bit. 
1

：

Next DMA EOT is the last transfer. 

0

：

Next DMA EOT is not the last transfer. 

Note: This bit is used in master receiver mode to 
permit  the  generation  of  a  NACK  on  the  last 
received data. 

0 

11 

DMAEN 

RW 

DMA  requests  enable  bit.

 

Set  this  bit  to  allow 

DMA request when TxE or RxEN is set. 

0 

10 

ITBUFEN 

RW 

Buffer interrupt enable bit. 
1

：

When TxE or RxEN is set, event interrupt is 

generated. 
0

：

When  TxE  or  RxEN  is  set,  no  interrupt  is 

generated. 

0 

9 

ITEVTEN 

RW 

Event interrupt enable bit.

 

Set this bit to enable 

event  interrupt.  This  interrupt  will  be  generated 
under the following conditions.  
SB=1 (Master mode). 
ADDR=1 (Master-slave mode). 
ADDR10 = 1 (Master mode). 
STOPF=1 (Slave mode). 
BTF = 1, but no TxE or RxEN events. 
TxE event to 1 if ITBUFEN = 1. 
RxNE event to 1if ITBUFEN = 1. 

0 

8 

ITERREN 

RW 

Error  interrupt  enable  bit.  Set  to  allow  error 
interrupts. 
The  interrupt  will  be  generated  under  the 
following conditions. 
BERR=1; ARLO=1; AF=1; OVR=1; PECERR=1. 
TIMEOUT=1; SMBAlert=1. 

0 

[7:6] 

Reserved 

RO  Reserved 

0 

[5:0] 

FREQ 

RW 

The  I2C  module  clock  frequency  field,  which 
must be entered at the correct clock frequency to 
produce  the  correct  timing,  allows  a  range 
between  2-36  MHz.  It  must  be  set  between 
000010b and 100100b in MHz. 

0 

 

13.11.3 I2C Own address register 1(I2C1_OAR1) 

Offset address: 0x08 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

ADD 

MOD

E 

Reserved 

ADD[9:8] 

ADD[7:1] 

ADD

0 

 

Bit 

Name 

Access 

Description 

Reset value 

15 

ADDMODE 

RW 

Address mode. 
1: 10-bit slave address (does not respond to 7-bit 
addresses). 

0 

Summary of Contents for CH32V003 Series






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands