WCH CH32V003 Series Reference Manual Download Page 108

Page: 108 / 181

CH32V003

Reference Manual

http://wch.cn

V1.3

108

CC2E

RW Compare the capture channel 2 output enable bit.

CC1NP

Compare capture channel 1 complementary output
polarity setting bit.

CC1NE

Compare capture channel 1 complementary output
enable bit.

CC1P

RW Compare capture channel 1 output polarity setting bit.

CC1E

RW Compare capture channel 1 output enable bit.

10.4.10 Counter for advanced-control timer (TIM1_CNT)

Offset address: 0x24

CNT[15:0]

Bit

Name

Access

Description

Reset

value

[15:0] CNT

RW The real-time value of the timer's counter.

10.4.11 Counting clock prescaler (TIM1_PSC)

Offset address: 0x28

PSC[15:0]

Bit

Name

Access

Description

Reset

value

[15:0] PSC

The dividing factor of the prescaler of the timer; the
clock frequency of the counter is equal to the input
frequency of the divider/(PSC+1).

10.4.12 Auto-reload value register (TIM1_ATRLR)

Offset address: 0x2C

ATRLR[15:0]

Bit

Name

Access

Description

Reset

value

[15:0] ATRLR

The value of this field will be loaded into the counter,
see section 10.2.3 for when the ATRLR acts and
updates; the counter stops when the ATRLR is empty.

10.4.13 Repeat count value register (TIM1_RPTCR)

Offset address: 0x30

Reserved

RPTCR[7:0]

Bit

Name

Access

Description

Reset

value

[15:8] Reserved

RO Reserved

[7:0]

RPTCR

RW The value of the repeat counter.

Summary of Contents for CH32V003 Series






















































































































































































Search results

Summary of Contents for CH32V003 Series

Reviews:

Brands by name

Popular brands

WCH CH32V003 Series, Reference Manual

Search results

Summary of Contents for CH32V003 Series

Reviews:

Brands by name

Popular brands