manualshive.com logo in svg

WCH CH32V003 Series, Reference Manual

Share
Download
WCH CH32V003 Series Reference Manual Download Page 1

 

 

 

 

CH32V003 Reference Manual 

V1.3

 

Overview 

CH32V003  series  are  industrial-grade  general-purpose  microcontrollers  designed  based  on  32-bit  RISC-V 
instruction set and architecture. It adopts QingKe V2A core, RV32EC instruction set, and supports 2 levels of 
interrupt nesting. The series are mounted with rich peripheral interfaces and function modules. Its internal 
organizational structure meets the low-cost and low-power embedded application scenarios. 

This  manual  provides  detailed  information  on  the  use  of  the  CH32V003  series  for  the  user's  application 
development,  and  is  applicable  to  products  with  different  memory  capacities,  functional  resources,  and 
packages in the series; any differences will be specially explained in the corresponding functional chapters. 

RISC-V core version overview 

Features

 
 
Core 
versions 

Instruction 

set 

Hardware 

stack 

levels 

Interrupt 

nesting 

levels 

Number of 

fast interrupt 

channels 

Integer 

division 

periodicity 

Vector 

table 

model 

Extensions 

instruction 

Memory 

protection 

QingKe 

V2A 

RV32EC 

2 

2 

2 

None 

Address 

or 

command 

Support 

None 

 
Abbreviated description of the bit attribute in the register: 

Register bit 

properties 

Property description 

RF 

Read-only property that reads a fixed value. 

RO 

Read-only attribute, changed by hardware. 

RZ 

Read-only property, auto bit clear 0 after read operation. 

WO 

Write only attribute (not readable, read value uncertain) 

WA 

Write-only attribute, writable in Safe mode. 

WZ 

Write only attribute, auto bit clear 0 after write operation. 

RW 

Readable and writable. 

RWA 

Readable, writable in Safe mode. 

RW1 

Readable, write 1 is valid, write 0 is invalid. 

RW0 

Readable, write 0 valid, write 1 invalid. 

RW1T 

Readable, write 0 invalid, write 1 flipped. 

 

Summary of Contents for CH32V003 Series






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands