WBOX Technologies 0E-16CHNVR2T User Manual Download Page 63

Page: 63 / 97

Setting

Network Video Recorder(NVR)

User Manual

Issue V1.0 (2018-05-11)

8.3.10 Alarm Input

Take the following steps to set alarm input:

Step 1

Setting

NVR Setup

Channel>Alarm Input

The

alarm input

interface is displayed, as shown in Figure 8-17.

Figure 8-17

Alarm Input

interface

Step 2

Select channel ID.

Step 3

Select alarm I/O channel.

Step 4

Input the I/O alarm name.

Step 5

Click

I/O Alarm

button to enable I/O alarm.

Step 6

Select the valid voltage level from the drop-down list box.

Step 7

When the alarm level is set to high, it will generate alarm signal when the COM

terminal and the IN terminal is connected; when the alarm level is set to low, it will
generate alarm signal when the COM terminal and the IN terminal is disconnected.

Step 8

Set schedule.

For details, see

8.3.7 Step 6 Set motion alarm schedule.

Step 9

Check

Channel Record

. Select a channel ID, input the post record to enable record

linkage.

Step 10

Check

Channel PTZ

. Select a channel ID and preset to enable PTZ linkage. Click

to add another Channel PTZ.

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands