WBOX Technologies 0E-16CHNVR2T User Manual Download Page 35

Page: 35 / 97

Video Playback

Network Video Recorder(NVR)

User Manual

Issue V1.0 (2018-05-11)

Figure 6-3

Backup path browse

dialog box

The

Backup Path

bar displays the selected backup path. If it is empty, select a backup

path. The list below shows available backup storage devices. The NVR supports two
types of backup storage device, that is, USB storage device and ESATA Disk.



USB Disk



Connect a USB flash drive or mobile hard disk to the USB interface on the front
panel.



The NVR detects and displays the USB disk automatically.



Right-click the USB flash drive and choose

Popup

Format

to perform the

corresponding operation.



Double-click the USB flash drive to access the corresponding path list, select a
backup path, and click

to save the setting and exit.



ESATA Disk



Connect a ESATA flash drive or mobile hard disk to the ESATA interface.



The NVR detects and displays the ESATA storage device automatically.



Double-click the ESATA flash drive to access the corresponding path list, select a
backup path, and click OK to save the setting and exit.

Step 2

Set backup file options.

Record File Size: specifies the maximum size of a single backup file.

Record File Type: specifies the type of record file.

Step 3

Select the video to be backed up.

Method 1: Select the video to be backed up during video playback. Figure 6-4 shows
the video backup control bar.

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands