WBOX Technologies 0E-16CHNVR2T User Manual Download Page 58

Page: 58 / 97

Setting

Network Video Recorder(NVR)

User Manual

Issue V1.0 (2018-05-11)

Step 3

Press and hold the left mouse button, and drag on the preview image to cover the part

to be masked.



Click the right mouse button on the preview image to clear the masked area.



You can click Reset to configure the masked area again.

Step 4

Click

Apply

. The message “Apply success” is displayed.

Step 5

Click

. The system saves the settings.

----End

8.3.7 Motion Alarm

The following functions are provided:



Enable motion alarm



Set motion alarm schedule



Set motion area



Set alarm linkage

Take the following steps to set motion alarm:

Step 1

Setting

NVR Setup

Channel>Motion Alarm

The

motion alarm

interface is displayed, as shown in Figure 8-12.

Figure 8-12

Motion Alarm

interface

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands