WBOX Technologies 0E-16CHNVR2T User Manual Download Page 42

Page: 42 / 97

Setting

Network Video Recorder(NVR)

User Manual

Issue V1.0 (2018-05-11)

Parameter

Description

Setting

DHCP IP

IP address of a camera, which is
set based on actual conditions

[How to set]

Enter an IP address in the
corresponding field.

[Default value]
192.0.0.64

Preferred DNS
Server

IP address of the DNS server

[How to set]

Enter the IP address of the
DNS server in the
corresponding field.

[Default value]

Alternate DNS
Server

IP address of a domain server.

If the preferred DNS server is
faulty, the device uses the
alternate DNS server to resolve
domain names.

[Setting method]

Enter a value manually.

[Default value]

Status

Status of NVR Ethernet interface.

Speed

Bandwidth of Ethernet interface.

P2P Status

P2P Status of NVR

QR Code

UUID QR code of NVR.

Step 3

Click

Apply

The "Apply success" prompt is displayed. Click OK.

If another prompt is displayed, check whether the parameters meet requirements
and re-set the parameters if necessary.

-----End

8.2.2 System

Step 1

Choose

Setting

NVR Setup

Device

System

The

System

interface appears, as shown in Figure 8-3.

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands