WBOX Technologies 0E-16CHNVR2T User Manual Download

Page: 19 / 97

Network Video Recorder(NVR)
User Manual

Operation Instruction

Issue V1.0 (2018-05-11)

Figure 3-4

NVR self-test

When the hardware abnormality is detected, the self-test screen stays on. You can click

continue

shutdown

in the lower right corner of the screen. If you click

continue

the NVR enters the login screen.

The hard disk of the NVR must be provided by the user. Hard disk detection is performed
during startup. If the detection fails, possible causes include

：



The hard disk is new and unformatted. The hard disk is formatted, but the file system is
inconsistent with the one supported by the NVR.



The hard disk is damaged.

3.4 Shutdown

To shut down the NVR after logging in to the main interface, click

and choose

Exit System in the upper right corner. The shutdown interface appears, as shown in
Figure 3-5.

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands