WBOX Technologies 0E-16CHNVR2T User Manual Download Page 53

Page: 53 / 97

Setting

Network Video Recorder(NVR)

User Manual

Issue V1.0 (2018-05-11)



Preferred Domain Name System (DNS) server



Alternate DNS server



MTU

Procedure

Step 1

Click

Setting

NVR Setup

Channel>Network

The

Network

interface appears, as shown in Figure 8-9.

Figure 8-9

Network

interface

Step 2

Set the parameters according to Table 8-5.

Table 8-5

Network parameters

Parameter

Description

Setting

IP Protocol

IPv4 is the IP protocol that uses
an address length of 32 bits.

IPv6 is the IP protocol that uses
an address length of 128 bits

[Setting method]

Select a value from the
drop-down list box.

[Default value]

IPv4

IP Address

Device IP address that can be set
as required.

[Setting method]

Enter a value manually.

[Default value]

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands