WBOX Technologies 0E-16CHNVR2T User Manual Download Page 40

Page: 40 / 97

Setting

Network Video Recorder(NVR)

User Manual

Issue V1.0 (2018-05-11)



Cameras Supported



Disks Supported



Among the preceding parameters, only

Device Name

can be modified.



The device information is updated automatically when the NVR is upgraded and keeps
consistent with the software version of the NVR.

8.2 Device

8.2.1 Network

On the

Network

interface, you can view the DHCP IP address (automatically obtained

IP address) of the NVR and set the IP address, subnet mask, preferred DNS server, and
alternate DNS server of the NVR.

If the NVR is deployed on a local area network (LAN), avoid an IP address conflict
between the NVR and any PC on the LAN and ensure that the IP addresses of network
interfaces 1 and 2 of the NVR are in different network segments.

Operation procedure

Step 1

Choose

Setting

NVR Setup

Device

Network

The

Network

interface appears, as shown in Figure 8-2.

Summary of Contents for 0E-16CHNVR2T


































































































Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands

WBOX Technologies 0E-16CHNVR2T, User Manual

Search results

Summary of Contents for 0E-16CHNVR2T

Reviews:

Related manuals for 0E-16CHNVR2T

Brands by name

Popular brands