Vollrath STL-80SS Operator'S Manual Download Page 71 | Manualshive

Page: 71 / 74

background image

68

The following maintenance tools are recommended utensils for the STL-80SS system cleaning
procedures. These items are not included with the system but are available for purchase through
www.PartsTown.com. Suitable alternatives for these maintenance items may be available. Contact
White Glove Service for more information. The following schedule has been prepared as a reference for
maintaining the cleaning tools.

*

THE BRUSHES WITH THE ASTERISK (*) INDICATE THE TOOL IS A PART OF THE MAINTENANCE

BRUSH KIT (PART #2209839)

ALTERNATE PARTS AND KITS BY FREEZER MODEL

Stoelting offers many equipment options and accessories through White Glove Service that may be
helpful for your operational or installation requirements. This includes adapter kits, adapters, brackets,
and switches for various freezer models. Please contact White Glove Service at 800-319-9549 or visit

www.PartsTown.com

and

www.flavorburst.com

for additional information concerning other optional

accessories, advertising and promotional materials.

RECOMMENDED MAINTENANCE ITEMS REPLACEMENT SCHEDULE

Part No.

Part Description

Every 3

months

Every 6

months

Annually

2209839

Maintenance Brush Kit

(includes items listed below)

Inspect & replace if

necessary

Minimum

208409*

Bristle Brush (1 ½” dia. x 4”)

Inspect & replace if

necessary

Minimum

208465*

Bristle Brush (1” dia.)

Inspect & replace if

necessary

Minimum

208387*

Bristle Brush (1/2” dia. x 5”)

Inspect & replace if

necessary

Minimum

208001*

Detail Brush (1/16” dia.)

Inspect & replace if

necessary

Minimum

«
...
69
70
71
72
73
...
»

Summary of Contents for STL-80SS











































































Reviews:

No comments

Related manuals for STL-80SS

Brand: Rainfresh Pages: 16

Brand: Ugolini Pages: 36

Brand: HÖR Pages: 9

Brand: corob Pages: 44

Brand: Millipore Pages: 2

Brand: American Plumber Pages: 4

Brand: Bunn Pages: 2

ADIKI300-01 Series

Brand: ADIR Pages: 18

Brand: GE Pages: 48

Brand: Silver King Pages: 4

Brand: Aquaport Pages: 8

Brand: Aquaport Pages: 12

Brand: Aquaport Pages: 12

Brand: Aquaport Pages: 12

Brand: Aquaport Pages: 16

Brand: BOWMAN Pages: 2

Brand: MARLO Pages: 48

EFA14VR 2EJO Series

Brand: Elkay Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands