Vollrath STL-80SS Operator'S Manual Download Page 52 | Manualshive

Page: 52 / 74

background image

49

3. Use the ampule provided to prime the

cleaned area before mounting the Touch
Panel mounting bracket.

NOTE

: LIQUID INSIDE THE AMPULE

ENHANCES ADHESION.

4. Set the mounting plate on the freezer where

it will be attached. Measure and mark with
a pencil around the base plate.

5. Remove the protective covering from the

adhesive strip on the bottom of the base
plate.

The front of the plate is the side

with the posts that are closest together

.

Apply the base plate to the freezer within
the pencil marks. Press firmly and allow the
adhesive to cure

for at least 1 hour

.

NOTE:

IF THE ADHESIVE DOES NOT HAVE

TIME TO CURE PROPERLY, THE CONSTANT
WEIGHT OF THE TOUCH PANEL CAN PULL
THE ADHESIVE AWAY FROM THE FREEZER
SURFACE. THIS COULD EVENTUALLY
RESULT IN THE TOUCH PANEL ASSEMBLY
FALLING OFF THE FREEZER.

6. Install the Touch Panel mounting plate to

the back of the Touch Panel using the
screws provided. Use the small lock
washers in between the plate and screws.

7. Connect the ethernet cable to the “DRIVER

BOARD 1” ethernet port behind the Touch
Panel screen.

NOTE:

WHILE “DRIVER BOARD 2” PORT IS

ALSO A VALID PORT, IT IS TEMPORARILY
PLUGGED TO AVOID CONFUSION. THE
COLOR TOUCH PANEL PROGRAM
DEFAULTS TO DRIVER BOARD 1.

8. Connect the straight end of the switch

extension to the “PORT 1” switch port
behind the Touch Panel screen.

NOTE:

WHILE “PORT 2” SWITCH PORT IS

ALSO A VALID PORT, IT IS TEMPORARILY
PLUGGED TO AVOID CONFUSION. YOU
WILL ACTIVATE THE PORT YOU USE WHEN
YOU GO THROUGH THE EQUIPMENT
SETUP WIZARD PROGRAM ON YOUR
COLOR TOUCH PANEL LATER.

«
...
50
51
52
53
54
...
»

Summary of Contents for STL-80SS











































































Reviews:

No comments

Related manuals for STL-80SS

Brand: WaterCare Pages: 7

Aqua-Pure AP Easy Series

Brand: 3M Pages: 24

Brand: lancer Pages: 16

LOGIX 255-760 Meter

Brand: Autotrol Pages: 15

ZIPPETTE PRO Series

Brand: JENCONS Pages: 48

AccuDose series

Brand: Hydro Pages: 4

Brand: Murdock Pages: 8

Brand: Murdock Pages: 17

INLINE CONNECT FS10

Brand: Propur Pages: 4

Brand: IRIT Pages: 2

Brand: American Changer Pages: 35

Brand: Hamilton Beach Pages: 17

Brand: Dacor Pages: 1

Brand: WaterSoft Pages: 28

Brand: Watts Pages: 44

Brand: Grunbeck Pages: 51

Brand: Tecno-gaz Pages: 44

FD7001 1H Series

Brand: Elkay Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands