Vollrath STL-80SS Operator'S Manual Download Page 10

Page: 10 / 74

General System Overview (See Figure 1)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

STOEELE906A

TOUCH PANEL ASSEMBLY WITH
BRACKET

Flavor Burst unit command center.

STOEINJ424STL-SS

FLAVOR BURST ASSEMBLY

Injects syrups into the product.

STOEMIS3026S

TOUCH PANEL CABLE CASING

Conceals and protects the Touch Panel
cable, as well as attaches it to the freezer.

STOEMIS3196

STAINLESS TUBE / CABLE
CASING ASSEMBLY

Attaches the flavor lines and/or cables to the
side of the freezer.

STOEELE525M

MALE TO MALE 48” SWITCH
EXTENSION

Connects Touch Panel to the freezer switch.

STOECAB113

FLAVOR TRAY

Houses syrup bags.

N/A

FLAVOR BURST SOFT SERVE
CABINET ASSEMBLY

Houses syrup trays and bags.

STOESYR944

SYRUP BAG CONNECTOR
ASSEMBLY

Transports syrup from the bag to the pumps.

STOESAN740

SANITIZER TANK ASSEMBLY

Houses sanitizer cleaning solution.

10 STOESPR5800STL-SS

SPARE PARTS KIT – SOFT
SERVE

Houses extra spare parts and wear items.

11 STOEELE434

POWER CABLE

Supplies the electronics board with power.

PARTS IDENTIFICATION/FUNCTIONS

Summary of Contents for STL-80SS











































































Search results

Summary of Contents for STL-80SS

Reviews:

Related manuals for STL-80SS

Brands by name

Popular brands

Vollrath STL-80SS, Operator'S Manual

Search results

Summary of Contents for STL-80SS

Reviews:

Related manuals for STL-80SS

Brands by name

Popular brands