Vertex Standard VX-3R Operating Manual Download | Manualshive

Page: 85 / 85

background image

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Part 15.21: Changes or modifications to this device not expressly approved by Vertex Standard could
void the user’s authorization to operate this device.

DECLARATION BY MANUFACTURER

The scanner receiver is not a digital scanner and is incapable of being converted or modified to a
digital scanner receiver by any user.

Vertex Standard Co., Ltd.

85

«
...
83
84
85

Summary of Contents for VX-3R






















































































Reviews:

No comments

Related manuals for VX-3R

Brand: Hama Pages: 32

FTDX-9000 - CAT OPERATION REFERENCE BOOK

Brand: Yaesu Pages: 12

Brand: Fly Sky Pages: 2

Brand: IDT Pages: 25

Brand: HobbyKing Pages: 2

Brand: Warner RF Pages: 7

Brand: Eltek Pages: 2

Brand: AOR Pages: 1

Brand: First Alert Pages: 1

Brand: Ham radio Pages: 14

Brand: MikroTik Pages: 2

Brand: Kanga Products Pages: 26

BTL7-A/E1 0-M-H-SA262-KA Series

Brand: Balluff Pages: 16

Brand: Marantz Pages: 52

Brand: GE MDS Pages: 211

Brand: SMAR Pages: 110

Brand: Cirronet Pages: 60

Brand: Vitek Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands