Vertex Standard VX-3R Operating Manual Download

Page: 81 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

HOLD: The scanner will halt on a signal it encounters. It will not restart automatically; you must

manually re-initiate scanning if you wish to resume.

Set Mode Item 76 [SCN.STR]

Function: Select the Scan Re-start Delay time.

Available Values: 0.1-0.4S (0.1S/step) or 1.0S - 10.0S (0.5S/step)

Default: 2.0S

Set Mode Item 77 [SP OUT]

Function: Enables/Disables the FM Broadcast audio output to the internal speaker when using the

earphone antenna.

Available Values: AUTO/SPKR

Default: AUTO

AUTO: The FM Broadcast audio output is selected automatically depending on the connection of

the earphone antenna.

SPKR: Outputs the FM Broadcast audio output to the internal speaker any time.

Set Mode Item 78 [SQ LVL]

Function: Sets the Squelch threshold level.

Available Values: LVL 0 - LVL 15 (AM and Narrow FM), LVL 0 - LVL 8 (Wide FM and AM

Broadcast)

Default: LVL 1 (AM and Narrow FM), LVL 2 (Wide FM and AM Broadcast)

Set Mode Item 79 [SQ TYP]*

Function: Selects the Sub Audible Squelch Type.

Available Values: OFF/TONE/TSQL/DCS/RV TN/PR FRQ/PAGER/MESSAGE

Default: OFF

TONE: Activates the CTCSS Encoder

TSQ: Activates the CTCSS Encoder/Decoder

DCS: Activates the Digital Coded Encoder/Decoder

RV TN: Activates the Reverse CTCSS Decoder (Mutes the receiver when matching tone is

received)

PR FRQ: Activates the User programmed Reverse CTCSS Decoder (Mutes the receiver when

user programmed matching tone* is received)

PAGER: Activates the Enhanced Paging & Code Squelch

MESSAGE: Activates the Message feature

Note: See also Set Mode Item 81: SQSPLT regarding additional selections available during “Split

Tone” operation.

* Determine from the Set Mode Item 63: PR FRQ.

Set Mode Item 80 [SQSMTR]*

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands