Vertex Standard VX-3R Operating Manual Download

Page: 71 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

Function: Enables/Disables the Busy Channel Lock-Out feature.

Available Values: ON/OFF

Default: OFF

Set Mode Item 9 [BEL.RNG]

Function: Selects the number of Bell ringer repetitions.

Available Values: 1T - 20T/CONT (Continuous ringing)

Default: 1T

Set Mode Item 10 [BEL.SEL]*

Function: Enables/Disables the Bell ringer function and its sound selection.

Available Values: OFF/BELL/USRBP1/ USRBP2/ USRBP3

Default: OFF

Set Mode Item 11 [BNK.NAM]

Function: Stores Alpha-Numeric “Tags” for the Memory Banks.

See page ?? for details.

Set Mode Item 12 [BP EDG]

Function: Enables/Disables the Band-edge beeper while selecting the frequency by the DIAL

knob.

Available Values: ON/OFF

Default: OFF

Set Mode Item 13 [BP LVL]

Function: Adjust the Beep volume level.

Available Values: LVL 1 - LVL 9

Default: LVL 5

Set Mode Item 14 [BP SEL]

Function: Enables/Disables the Keypad beeper.

Available Values: OFF/KY+SCN/KEY

Default: KY+SCN

OFF: The Beeper is disabled.

KY+SCN: The beeper sounds when you press a key or when the scanner stops.

KEY: The beeper sounds when you press any key.

Set Mode Item 15 [BP USR]

Function: Create the beep melody for Bell ringer function.

See page ?? for details.

Set Mode Item 16 [BSY.LED]

Function: Enables/Disables the BUSY LED while the Squelch is open.

Available Values: ON/OFF

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands