Vertex Standard VX-3R Operating Manual Download

Page: 78 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

See page ?? for details.

Set Mode Item 57 [MSG.SEL]

Function: Programming a Message for the Message feature.

See page ?? for details.

Set Mode Item 58 [ON TMR]

Function: Set the On Timer Time.

Available Values: OFF/00H.10M(00:10) 24H.00M(24:00) (10 minutes/step)

Default: OFF

The On Timer turns on the radio at the programmed time.

Set Mode Item 59 [OPN.MSG]

Function: Selects the Opening Message that appears when the radio is powered on.

Available Values: OFF/DC/MSG

Default: DC

OFF: No Opening Message

DC: DC supply voltage

MSG: Set by user. See below.

Here’s how to program the Opening Message:

1. Select this Set Mode Item to “MSG.”

2. Press the [V/M] key momentarily to enable programming of the opening message. You will

notice the first character entry’s location blinking.

3. Rotate the DIAL knob to select the first letter/number of the message, then press the [V/M]

key momentarily to save the first letter/number and move on to the next character.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob

4. Repeat the steps 3 and 4 as necessary to complete the message (up to six characters).

5. If you make a mistake, press the [BAND] key to back-space the cursor; now re-enter the

correct letter/number.

6. When you have entered the desired opening message, press the [TXPO] key momentarily to

confirm the message, then press the PTT switch to save the settings and exit to normal

operation.

Set Mode Item 60 [PAG.ABK]

Function: Enables/Disables the Answer Back function of the Enhanced CTCSS Paging & Code

Squelch.

Available Values: ON/OFF

Default: OFF

Set Mode Item 61 [PAG.CDR]

Function: Sets the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands