Vertex Standard VX-3R Operating Manual Download

Page: 76 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

INT MR: Recall the Internet Access Number (SRG) or Access Cord (FRG). Determine the

selection of the SRG or FRG via Set Mode Item 41: INT MD.

SET MD: Short-cut path for recall of one of Set Mode Items. See page ?? for programming.

Set Mode Item 43 [INTNET]

Function: Enables/Disables the Internet Connection feature (WIRES

Available Values: ON/OFF

Default: OFF

Set Mode Item 44 [LAMP]

Function: Selects the LCD/Keypad Lamp mode.

Available Values: KEY 2S - KEY10S/CONT/OFF

Default: KEY

KEY 2S - KEY10S: Illuminates the LCD/Keypad for the selected illumination time when any key is

pressed.

CONT: Illuminates the LCD/Keypad continuously.

OFF: Disables the LCD/Keypad illumination

Set Mode Item 45 [LED LT]

Function: Illuminates the TX/BUSY indicator glows continuously white (useful as emergency

flashlight at night).

Set Mode Item 46 [LOCK]

Function: Selects the Control Locking lockout combination.

Available Values: KEY/PTT/KY(KEY)+PTT

Default: KEY

Set Mode Item 47 [M/T-CL]

Function: Selects the MONI key (just below the PTT switch) function.

Available Values: MONI/T-CALL

Default: Depends on the transceiver version.

MONI: Pressing the MONI key causes the Noise/Tone Squelch to be over-ridden, allowing you to

listen for weak (or non-encoded) signals.

T-CALL: Pressing the MONI key activates a 1750-Hz burst tone, used for repeater access in many

countries (especially in Europe).

Set Mode Item 48 [MCGAIN]

Function: Adjust the microphone gain level.

Available Values: LVL 1 - LVL 9

Default: LVL 5

This Set Mode setting is affect to both internal and external microphone.

Set Mode Item 49 [MR DSP]*

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands