Vertex Standard VX-3R Operating Manual Download

Page: 79 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

See page ?? for details.

Set Mode Item 62 [PAG.CDT]

Function: Sets the Transmitting Pager Code for the Enhanced CTCSS Paging & Code Squelch.

See page ?? for details.

Set Mode Item 63 [PR FRQ]*

Function: Program the CTCSS Tone frequency for the User programmed Reverse CTCSS

Decoder.

Available Values: 300Hz - 3000Hz (1000 Hz/step)

Default: 1600 Hz

Set Mode Item 64 [PRI.RVT]

Function: Enables/Disables the Priority Revert feature.

Available Values: ON/OFF

Default: OFF

See page ?? for details.

Set Mode Item 65 [PRI.TMR]

Function: Select the periodically checking time for the Priority (Dual Watch) feature.

Available Values: 0.1 - 0.9S (0.1S/step) or 1.0S - 10.0S (0.5S/step)

Default: 5.0S

See page ?? for details.

Set Mode Item 66 [PSWD]

Function: Programs and activates the Password feature.

See page ?? for details.

Set Mode Item 67 [PTT.DLY]

Function: Select the time delay between the PTT switch is pressed and the carrier is transmitted.

Available Values: OFF/20MS/50MS/100MS/200MS

Default: OFF

Set Mode Item 68 [RPT]*

Function: Sets the Repeater Shift Direction.

Available Values: SIMP/-RPT/+RPT

Default: Depends on the transceiver version, as well as the setting of Set Mode Item 5 [ARS].

Set Mode Item 69 [RPT.SFT]*

Function: Sets the magnitude of the repeater Shift.

Available Values: 0.00 - 150.00 MHz (50 kHz/step)

Default: Depends on the operating band and transceiver version.

If you press the [F/W] key momentarily, then rotate the DIAL knob, frequency steps of 1 MHz will

be selected.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands