Vertex Standard VX-3R Operating Manual Download

Page: 69 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

Set (Menu) Mode

The VX-3R Set Mode, already described in parts of many previous chapters, is easy to activate and set. It

may be used for configuration of a wide variety of transceiver parameters, some of which have not been

detailed previously. Use the following procedure to activate the Set Mode:

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select the Set Mode Item to be adjusted.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of the Set Mode Item.

Rotate the DIAL knob to adjust or select the parameter to be changed on the Set Mode Item selected in

above step.

5. After completing your selection and adjustment, press the PTT switch momentarily to save the new

setting and exit to normal operation.

R.F. Says:

Some Set Mode Items (like Set Mode Item 86: TN FRQ) require that the [TXPO] key be pressed

after setting of the parameter, and before exiting to normal operation.

Masking the Set Mode Items

There may be situations where you want to “Mask” Set Mode Items so they are not recall during Set Mode

Item selection.

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select the Set Mode Item 33: EXT.MNU.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of the Set Mode Item.

4. Rotate the DIAL knob to select “ON”, then press the [TXPO] key momentarily.

5. Rotate the DIAL knob to select the Set Mode Item to be “Masked”.

6. Press the [F/W] key momentarily. A small “ ” icon will appear at the above of the volume level indicator

on the display; indicating it is to be Masked Set Mode Item.

7. Rotate the DIAL knob; the previously-selected Set Mode Item will be “Masked”.

8. Repeat steps 5 - 7 above, to append the “ ” icon to any other Set Mode Item you wish to “Masked”.

9. Press the PTT switch momentarily to save the new setting and exit to normal operation.

To unmask the hidden Set Mode Item, repeat above procedure: select “OFF” in step 4 above and disappear

the “ ” icon in step 6 above from the Set Mode Item you wish to unmasked.

Set Mode Summary

Note: A Set Mode Item with a * mark can set/select a selection to the memory channel individually.

Set Mode Item 1 [ANT AM]

Function: Select the antenna to be used in the AM Broadcast listening.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands